Magyar
English
AIJGO-32 Personal grounding tester
The AIJGO-32 is a tester for checking personal grounding before entering an ESD protected area (EPA). It may be a good choice if you want to identify persons entering the site and link the tester to some kind of enterprise management system, time-tracking software or other program. The hardware of the device itself allows connection to any system via a serial port, but the software operation of the connection requires a driver, which need to be developed separately according to the customer’s needs. Such software is not provided with the device, but we can help you to develop it by providing product descriptions and informaton on interface programming. Based on this, the necessary additional driver can be created to ensure proper communication between the AIJGO product and the system.
The AIJGO-32 tester, with a properly functioning sytem and driver software programmed for it, can also allow you to apply more specific custom settings, such as how many times per day an employee is required to test, how many times per day he/she is allowed to enter without testing.
The AIJGO-32 product does not include management software. It is a tester with LIGHT BAR system – such AIJGO products have a steel touch button, the measured results are indicated by LED lights. COMFORT system product – such AIJGO devices have touch button and RFID reader, an RFID card is required for use.
The tester is supplied with manufacturer’s calibration certificate, dual foot electrode, mounting plate and universal holder.
AIJGO-32 PERSONAL GROUNDING TESTER
WITH DUAL FOOT ELECTRODE AND RFID READER
| ABOUT THE PRODUCT |
- Tester for checking personal grounding before entering an ESD protected area (EPA)
- Testing footwear system and wrist strap/groundable ESD smock system at the same time
- Can be used to test a groundable ESD smock system
- Test result indication with LED light and sound
- It is not possible to configure it so that a test can be carried out without touching the touch button
- With a built-in RFID reader
- We declare that the AIJGO-32 product complies with the requirements of IEC 61340-5-1, ANSI/ESD S20.20 and Directive 2001/95/EC (General product safety).
- For indoor use only
| Test voltage | 100 V DC |
| Wrist strap/groundable ESD smock system connection | With a combined 10 mm snap, 4 mm banana plug socket |
| Power supply | 12 V DC |
| Relay outputs | 0,5 A/60 V Pass relay (Normally Open) with green wire Fail relay (Normally Open) with red wire |
| D-SUB = RS232 serial port connection, made possible by a four-wire cable with a connector, TX, RX, GND (ground) and power (12 V) wires. The use of the power cable is not required. | |
| Sizes | 215 x 195 x 55 mm (tester) 500 x 630 x 970 mm (tester+stand with dual foot electrode, assembled), the touch button and the RFID reader emerges from it beyond this, the tester extends 14 cm backwards beyond the platform. The size of the platform itself (for tester version with stand): 500 x 490 x 20 mm. Tilt angle of the stand: 5 degrees |
| RFID READER |
FF reader (full frequency), it reads cards operating at low (125/134 kHz) and high (13,56 MHz) frequencies.
| It is prepared for the following types of cards, transmitters and communication: |
| Emarine (pl. EM4100,4102,4200), Casi Rusco, FDX Animal, HiTag1, HiTag2, Indala Type1, Indala Type2, Indala KSF (Kantech Secure Format), IoProx XSF (Kantech Extended Secure Format), ProxCard II, ProxCard II C1000, ProxCard II H10301, ProxCard II H10302, ProxCard II H10304, TIRIS, T5557, ATA5567, ATA5577 |
| Transmitters type ISO-14443A |
| Mifare Classic 1K, 4K, Mifare Ultralight, Mifare Desfire, Mifare Plus, Mifare Plus X, Mifare ProX, Mifare SmartMX, SLE66R35, NTAG213, NTAG215, NTAG216 |
| Transmitters type ISO-15693 |
| Texas Instruments TagIt Plus, Texas Instruments TagIt Plus 3P, Texas Instruments TagIt Standard, Texas Instruments TagIt Pro, Legic Advant, Picopass, HID iClass, ICode SLI, ICode 2 |
| Transmitters type ISO-14443B |
| SRIXXX, pl. SRI512, SRT512, SRI4K, SRIX4k, ISO-14443B card emulation |
| ISO-18092/NFC type communication |
| P2P active communication according to NFCIP-1, NFC card emulation (passive), NFC-enabled mobile phone (Android, iOS, Windows Mobile) in the previously listed modes |
Mounting plate sizes
| REQUEST FOR QUOTATION |
| ORDER CODE | TYPE | |
|---|---|---|
| AIJGO-32 | Personal grounding tester with dual foot electrode, RFID reader, mounting plate and universal holder | {AIJGO-32} |
| AIJGO-STA | Stand for AIJGO tester | {AIJGO-STA} |
